About this Product
DYCO SHIELD &SEAL is a solvent based polyurethane water proofing sealer designed to seal and protect epoxy bonded, natural stone surfaces such as Chattahoochee Stone, River Rock, and their supporting members such as retainer and expansion joints. It seals and helps protect them from standing water and moisture intrusion.
RECOMMENDED USES: Chattahoochee Stone and River rock Surfaces usually found in driveways, walkways, patios and pool decks.
FEATURES/BENEFITS:
Seals and Protects Surfaces
Resistant to Moisture Penetration
Resistant to Abrasion
Resistant to Grease, Oil and Detergent.
Product Specifications:
- Detailed Specifications
- Product Insights
- Product Features
- Usage Instructions
- Resources
- Product Reviews
Dyco SHIELD & SEAL is a solvent based polyurethane water proofing sealer designed to seal and protect epoxy bonded, natural stone surfaces such as Chattahoochee Stone, River Rock, and their supporting members such as retainer and expansion joints. It seals and helps protect them from standing water and moisture intrusion.
RECOMMENDED USES: Chattahoochee Stone and River rock Surfaces usually found in driveways, walkways, patios and pool decks.
FEATURES/BENEFITS:
• Seals and Protects Surfaces
• Resistant to Moisture Penetration
• Resistant to Abrasion
• Resistant to Grease, Oil and Detergent.
RECOMMENDED USES: Chattahoochee Stone and River rock Surfaces usually found in driveways, walkways, patios and pool decks.
FEATURES/BENEFITS:
• Seals and Protects Surfaces
• Resistant to Moisture Penetration
• Resistant to Abrasion
• Resistant to Grease, Oil and Detergent.
DYCO SHIELD &SEAL is a solvent based polyurethane water proofing sealer designed to seal and protect epoxy bonded, natural stone surfaces such as Chattahoochee Stone, River Rock, and their supporting members such as retainer and expansion joints. It seals and helps protect them from standing water and moisture intrusion.
RECOMMENDED USES: Chattahoochee Stone and River rock Surfaces usually found in driveways, walkways, patios and pool decks.
FEATURES/BENEFITS:
Seals and Protects Surfaces
Resistant to Moisture Penetration
Resistant to Abrasion
Resistant to Grease, Oil and Detergent.
Product Specifications:
PRECAUTION: Do not freeze. Wear protective clothing and eyewear during application of this product. Do not transport on passenger seats or inside passenger compartment of any vehicle. Store product in cargo area of vehicle, and secure with protective cloths to prevent accidental spill damage. Do not store at temperature above 100°F (37°C). Do not use in drinking water or food systems.
READ AND FOLLOW ALL DIRECTIONS: Surfaces must be clean, dry and sound. Contaminants such as dirt, dust, grease, wax, oil, soap film, rust, mold, mildew, bond breakers and curing compounds must be removed before application. Loose, chipping and peeling of previous coating must be removed before application. Clean surfaces with bleach solution [one (1) part bleach to four (4) parts water] and a stiff bristle brush. If mildew is present, treat with a mildew remover. Rinse with clean water and let dry one (1) to two (2) days before application. Do not apply to damp surfaces or when surface temperature is below 50°F (10°C) or above 100°F (37°C). Do not apply if rain is prevalent. Do not thin.
SLIPPERY WHEN WET: If the surface to be coated is exposed to water from rain, sprinklers, pools or by other means or if the surface is an inclined plane, such as a ramp or if concrete steps are being coated, Dyco recommends mixing SKID GARD #45 at 0.2lbs per gallon. If SKID GARD #45 is not avaliable, see your paint specialist for a recommendation of a suitable aggregate to be used at 0.2lbs per gallon. Stir vigorously to suspend SKID GARD #45 in the container before application. Note: Adding SKID GARD to transparent or semi-opaque coatings may alter the final appearance. Test the coating on a hidden area before applying to the entire surface.
PREPARING NEW UNCOATED SURFACES: On new and uncoated stone surfaces, follow manufacturer’s cleaning directions. For best results, clean with a degreaser and/ or pressure wash.
PREPARING PREVIOUSLY COATED SURFACES: If stone surface have been sealed with a water-based latex sealer, clean with a degreaser and/or pressure wash.
APPLICATION: Mix thoroughly before use. Shield & Seal is a two (2) coat process. Apply first coat evenly with a phenolic core (solvent resistant) medium nap roller, brush or airless sprayer. Allow three (3) hours and re-apply. Apply second coat at right angle to first coat. Coverage is 150-200 sq. ft./gal. depending on surface porosity and application method. This product is intended to glaze the top surface of the stones. Do not saturate the surface with each coat. When applying by roller, apply Shield & Seal with overlapping strokes in the same direction eliminating missed surfaces. Do not dry roll. Dries to touch in three (3) hours @ 77°F (25°C) and 50% R.H. Ready for foot traffic in eight (8) hours and vehicle traffic in 72 hours. Low temperature, high humidity, thick films or poor ventilation will increase these dry times.
Refer to Safety Data Sheet for additional health and safety information.
Refer to Product Spec Sheet for additional application details and further information.
- Choosing a selection results in a full page refresh.
- Press the space key then arrow keys to make a selection.