Detailed Specifications

Dyco® POOL DECK™ is a waterborne acrylic finish with superior film properties designed to provide a low sheen hard protective finish on concrete surfaces. POOL DECK is formulated with Ultraviolet (UV) and Infrared (IR) inhibitors for a long lasting finish. POOL DECK is resistant to harsh pool chemicals.
CHARACTERISTICS
• Dyco 9050 Pool Deck Waterborne Acyclic Stain is specifically formulated for use on Pool Deck surfaces with a low sheen and
• hard protective finish. May be applied to old deck paints if firmly
• bonded to the deck surface. Self priming when applied to bare
• concrete pool deck surfaces. Easy to use and cleans up with
• soap and warm water.

Product Insights

RECOMMENDED USES

• New Concrete Pool or Patio Decks

• Previously Painted Pool or Patio Decks

• New Kool Deck Surfaces

Product Features

Usage Instructions

 

FOR USE ON: Concrete surfaces usually found in pool decks, spa areas, patios, walkways and lanais.

READ AND FOLLOW ALL DIRECTIONS: Surfaces must be clean, dry and sound. Contaminants such as dirt, dust, grease, wax, oil, soap film, rust, mold, mildew, bond breakers and curing compounds must be removed be[1]fore application. Loose, chipping and peeling of previous coating must be removed before application. Repair holes and cracks with an appropriate patching material. Clean surfaces with bleach solution [one (1) part bleach to four (4) parts water] and a stiff bristle brush. If mildew is present, treat with a mildew remover. Rinse with clean water and let dry one (1) to two (2) days before application. Do not apply to damp surfaces or when surface temperature is below 50 °F (10 °C) or above 100 °F (37 °C). Do not apply if rain is prevalent. Do not thin.

SLIPPERY WHEN WET: Dyco recommends mixing SKID GARD #45 at 0.2lb. (3.2oz.) per gallon to the final coat if surface to be coated is a ramp, steps, or inclined plane; or is exposed to water from rain, sprinklers, pools or other means. If SKID GARD #45 is not available, see your paint specialist for a recommendation of a suitable aggregate to be used. NOTE: Adding SKID GARD to nonopaque coatings may alter final appearance. Test coating on a hidden area before applying to the entire surface.

PREPARING NEW AND PREVIOUSLY COATED SURFACES: Allow new exterior concrete to cure a minimum of 30 days before application. Pressure cleaning is recommended. Acid etching is not required. For previously coated surfaces, use DYCO 9040 TUFF GRIP as a bonding primer.

TINTING: Tint appropriate tint bases with approved colorants. Factory-tinted colors cannot be re-tinted unless indicated on label as tintable. When selecting colors, dark colors are better for high traffic areas and light colors are preferable for foot traffic areas such as patios, pool decks and walkways since light colors are cooler.

 APPLICATION: Mix thoroughly before use. POOL DECK is a two (2) coat process. Apply first coat evenly with a medium nap roller, brush or airless sprayer. Do not leave puddles or roller marks. Coverage is 175-225 sq. ft./gal. depending on surface porosity and application method. Allow two (2) hours before applying the second coat. For color uniformity of the finish coat, combine and stir all containers together into one container. For a non-skid surface add DYCO SKID GARD Skid Resistant Texture Additive. Dries to touch in two (2) hour @ 77 °F (25 °C) and 50% Relative Humidity. Ready for recoat in two (2) hours. Ready for foot traffic in four (4) hours. Low temperature high humidity, thick films or poor ventilation will increase these dry times.

TOOLS & APPLICATORS / CLEANING: Medium nap roll[1]er, brush or airless sprayer. Cleans with soap and water. PRECAUTION: Do not freeze. Wear protective clothing and eyewear during application of this product. Do not transport on passenger seats or inside passenger compartment of any vehicle. Store product in cargo area of vehicle, and secure with protective cloths to prevent accidental spill damage. Do not store at temperatures above 100 °F (37 °C). Do not use in drinking water or food systems.

WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREG[1]NANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at1-800-424-LEAD or log on to www.epa.gov/ lead.

Resources

Safety Data Sheet (SDS)

Technical Data Sheet (TDS)

Sale Sheet