About this Product
IAQ 4000 is a latex metal coating that inhibits rust on ferrous metal, galvanized metal and other surfaces exposed to general industrial and atmospheric conditions. The water-resistant coating can be used on new and previously coated roof decks, metal paneling, structural steel, corrugated metal siding, and miscellaneous iron and bar joists. SURFACE PREPARATION Remove all oil, grease, dirt, loose or scaling paint, rust, mil scale and other foreign matter. CLEAN ALL MOLD INFESTED SURFACES WITH IAQ 2000 SERIES DISINFECTANT/CLEANER. GALVANIZED METAL Surface oil should be wiped off with mineral spirits and a clean rag. PREVIOUSLY PAINTED SURFACES Prepare ruptured or scratched surfaces as for unfinished metal. Spot prime bare ferrous metal as conditions dictate. APPLICATION TOOLS Fiberlock IAQ 4000 can be applied by roller, brush or airless spray. Brush: Nylon or polyester synthetic bristle Roller: Synthetic fiber 3/8” or longer Spray Settings: pressure: 1500-2500 P.S.I. Tips: .017 to .021 tips PRODUCT APPLICATION Stir thoroughly with a lifting action to fully incorporate pigments. Fiberlock IAQ 4000 is supplied at application consistency, but can be thinned sparingly with water to improve application consistency if necessary. Apply with appropriate application equipment. Apply 2 coats of Fiberlock IAQ 4000. Finish coat will seal spots of ‘flash rusting’ which may appear on ferrous metal after first coat. DRYING TIME @ 70°F 50% R.H To Touch – 1 hour Recoat – 1 hour Full Cure – 10 days COVERAGE Smooth Surfaces: 400-450 ft2/gal. Porous Surfaces: 250-300 ft2/gal. CLEANUP Clean tools and drippings with warm soapy water before Fiberlock IAQ 4000 dries. Dispose of all waste according to all existing local, state and federal regulations. PRECAUTIONS Store in a dry place at temperatures between 40°F (4.5°C) and 90°F (32°C). Stir thoroughly. Do not mix with any other coatings, solvents or colors in oil. Do not apply Fiberlock IAQ 40
Product Specifications:
IAQ 4000 is a white, rust inhibiting, 100% acrylic latex metal coating for use on ferrous metal, galvanized metal and other surfaces exposed to general industrial and atmospheric conditions. IAQ 4000 has excellent water resistance and excellent resistance to most alkalis, detergents and mild acids. IAQ 4000 is ideal for both new and previously coated roof decks, metal paneling, structural steel, corrugated metal siding, and miscellaneous iron and bar joists.
- Fast drying
- Water-based formula
- 100% acrylic
- Excellent resistance to most alkalis, detergents and mild acids
- MFG SKU: 8340-5
PRECAUTIONS
- Store in a dry place at temperatures between 40°F (4.5°C) and 90°F (32°C).
- Stir thoroughly. Do not mix with any other coatings, solvents or colors in oil.
- Do not apply Fiberlock IAQ 4000 when air or surface temperature is below 50°F or when drying conditions are poor.
- Keep from freezing.
- IAQ 4000 is not designed for tank interiors or immersion services.
- When applying with a sprayer, wear a NIOSH approved respirator with any R, P, N or HE filter.
SURFACE PREPARATION
Remove all oil, grease, dirt, loose or scaling paint, rust, mil scale and other foreign matter. CLEAN ALL MOLD INFESTED SURFACES WITH IAQ 2000 SERIES DISINFECTANT/CLEANER.
GALVANIZED METAL
Surface oil should be wiped off with mineral spirits and a clean rag.
PREVIOUSLY PAINTED SURFACES
Prepare ruptured or scratched surfaces as for unfinished metal. Spot prime bare ferrous metal as conditions dictate.
APPLICATION TOOLS
Fiberlock IAQ 4000 can be applied by roller, brush or airless spray.
- Brush: Nylon or polyester synthetic bristle
- Roller: Synthetic fiber 3/8” or longer
- Spray Settings: pressure: 1500-2500 P.S.I. Tips: .017 to .021 tips
PRODUCT APPLICATION
Stir thoroughly with a lifting action to fully incorporate pigments. Fiberlock IAQ 4000 is supplied at application consistency, but can be thinned sparingly with water to improve application consistency if necessary. Apply with appropriate application equipment. Apply 2 coats of Fiberlock IAQ 4000. Finish coat will seal spots of ‘flash rusting’ which may appear on ferrous metal after first coat.
DRYING TIME
- @ 70°F 50% R.H
- To Touch – 1 hour
- Recoat – 1 hour
- Full Cure – 10 days
COVERAGE
- Smooth Surfaces: 400-450 ft2/gal.
- Porous Surfaces: 250-300 ft2/gal.
CLEANUP
Clean tools and drippings with warm soapy water before Fiberlock IAQ 4000 dries. Dispose of all waste according to all existing local, state and federal regulations.
PRECAUTIONS
Store in a dry place at temperatures between 40°F (4.5°C) and 90°F (32°C). Stir thoroughly. Do not mix with any other coatings, solvents or colors in oil. Do not apply Fiberlock IAQ 4000 when air or surface temperature is below 50°F or when drying conditions are poor. Keep from freezing. IAQ 4000 is not designed for tank interiors or immersion services. When applying with a sprayer, wear a NIOSH approved respirator with any R, P, N or HE filter.
- Choosing a selection results in a full page refresh.
- Press the space key then arrow keys to make a selection.