About this Product
Protect your surfaces against the growth of mold and mildew with Fiberlock AfterShock Fungicidal Coating. EPA registered as an antimicrobial coating designed to kill residual mold and mildew after pre-cleaning the contaminated surface, this mold killing coating is ideal for addressing mold growth from water damage. It also inhibits the future growth and spread of mold and mildew on the cured film surface. It's extremely durable and easy to apply with a brush, roller or airless sprayer. Follow all directions on label.
Fiberlock Technologies was founded upon the simple promise of providing the highest quality product and the best possible service to its customers while conducting business with the utmost integrity. Founded on the core beliefs that superior quality, definitive science and enduring service are the keys to corporate success, Fiberlock has grown to become one of the most respected names in the abatement and remediation industry.
Product Specifications:
- FUNGICIDAL COATING: Kill residual mold and mildew and protect your surfaces against future growth with Fiberlock AfterShock Fungicidal Coating.
- EPA REGISTERED COATING: AfterShock is EPA registered as an antimicrobial coating to kill mold and mildew after pre-cleaning contaminated surfaces. It provides extreme durability for long-lasting mold control.
- IDEAL FOR USE ON interior wall surfaces such as plaster, wallboard, drywall, concrete, masonry block, wood, primed metal and galvanized metal.
- EASY TO APPLY: Ensure surface is clean and free of surface damage. Apply AfterShock with a brush, roller or airless spray equipment. Follow all directions on label.
- FOR OVER 35 YEARS, Fiberlock Technologies has manufactured products used to address environmental, safety and health hazards, becoming one of the most respected names in the abatement and remediation industry.
AfterShock is an EPA registered antimicrobial coating designed to kill residual mold and mildew remaining after pre-cleaning contaminated surfaces. AfterShock also inhibits the future growth and spread of mold and mildew on the cured film surface in residential and institutional buildings. This extremely durable, easy to apply, 100% acrylic sealant offers the ultimate in durability in combination with excellent fungicidal characteristics to address mold growth from water damage. AfterShock is recommended for use on interior wall surfaces such as plaster, wallboard, drywall, concrete, masonry block, wood, primed metal and galvanized metal. AfterShock is also recommended for use on interior wood framing, primed metal, concrete, and wallboard inside the wall cavity. Do not use for HVAC system applications.
- EPA-registered fungicidal coating
- Kills and prevents mold and mildew
- 100% acrylic sealant
- MFG SKU: 8390-1, 8390-5
PRECAUTIONS
- It is a violation of Federal law to use this product in a manner inconsistent with its labeling. Do not contaminate water, food or feed by storage or disposal.
- PESTICIDE STORAGE: Close container after each use. Keep from freezing. Store in a dry place at temperatures between 40°F (4.5°C) and 90°F (32°C).
- PESTICIDE DISPOSAL: Wastes resulting from the use of this product may be disposed of on site or at an approved waste disposal facility.
- CONTAINER DISPOSAL: Triple rinse (or equivalent). Then offer for recycling or reconditioning, or puncture and dispose of in a sanitary landfill, or incineration, or, if allowed by state and local authorities, by burning. If burned, stay out of smoke.
SURFACE PREPARATION
AfterShock is supplied ready to use. Stir thoroughly. Do not mix with other coatings, solvents or colors in oil. Remove damaged materials and clean surfaces. Surface must be free of dust, mildew, mold, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap and other surface contamination. Patch surface irregularities with an appropriate patching compound. AfterShock is self-priming over bare gypsum drywall, composition board, ceiling tile and concrete. Do not apply when air or surface temperature is below 50°F or when drying conditions are poor. Use adequate ventilation during application.
DRYWALL
Joint cement should be sanded smooth, but avoid abrading the paper.
FERROUS METAL
Clean, then prime with Fiberlock IAQ™ 4000 acrylic DTM primer.
WOOD
Seal knots and stains with Fiberlock IAQ 5000 stain-blocking primer.
MASONRY BLOCK
Apply one coat of Fiberlock IAQ 3000 acrylic block filler if a denser surface is desired.
APPLICATION TOOLS
Apply AfterShock with a brush, roller or airless spray equipment.
- Brush: Synthetic, nylon or polyester bristle
- Roller: Synthetic fiber 3/8” nap or longer
- Spray Settings Pressure: 2000-3000 P.S.I. Tips: .017 to .021 tips
PRODUCT APPLICATION
Remove gross filth or heavy soil. For heavily soiled areas, a pre-cleaning step is required. Apply AfterShock generously and uniformly by brush, roller or airless spray and ensure that the surface is completely coated. Allow to air dry. Clean and inspect regularly for damage to coating film – reapply if cured coating film becomes damaged. AfterShock will kill residual mold and mildew on the surface, and then will prevent the growth of mold and mildew on the surface of the cured film.
COVERAGE
- Smooth Surfaces- 250-400 sq. ft. per gallon
- Porous Surfaces- 150-300 sq. ft. per gallon
DRYING TIME
- @ 70°F 50% R.H
- To Touch – 1 Hour
- Recoat – 4 Hours
CLEANUP
Clean tools and drippings with warm soapy water before AfterShock dries. Dispose of all waste according to all existing local, state and federal regulations.
PRECAUTIONS
It is a violation of Federal law to use this product in a manner inconsistent with its labeling. Do not contaminate water, food or feed by storage or disposal. PESTICIDE STORAGE: Close container after each use. Keep from freezing. Store in a dry place at temperatures between 40°F (4.5°C) and 90°F (32°C). PESTICIDE DISPOSAL: Wastes resulting from the use of this product may be disposed of on site or at an approved waste disposal facility. CONTAINER DISPOSAL: Triple rinse (or equivalent). Then offer for recycling or reconditioning, or puncture and dispose of in a sanitary landfill, or incineration, or, if allowed by state and local authorities, by burning. If burned, stay out of smoke.
Clean-Kill-Coat 3 Step Process for Mold & Water Damage
- Choosing a selection results in a full page refresh.
- Press the space key then arrow keys to make a selection.