Fiberlock Wet Wrap 'N' Seal Thermal Insulation Repair – Pro Solutions Direct

Fiberlock Wet Wrap 'N' Seal Thermal Insulation Repair

  • Load image into Gallery viewer, Fiberlock Wet Wrap 'N' Seal Thermal Insulation Repair
Fiberlock Wet Wrap 'N' Seal Thermal Insulation Repair
Fiberlock Wet Wrap 'N' Seal Thermal Insulation Repair
Fiberlock Wet Wrap 'N' Seal Thermal Insulation Repair

Fiberlock Wet Wrap 'N' Seal Thermal Insulation Repair

$242.99
$242.99
$242.99
MFG SKU: 2433-U
Stock: Out of Stock In Stock

Many of our products have bulk discounts for customers in our Pro Program. Sign up for our Pro Program here.

Purchase Options
Delivery Frequency
$242.99
$242.99
$242.99

About this Product

Wet Wrap 'N' Seal Thermal Insulation Repair by Fiberlock Technologies provides a permanent insulation encasement and repair to pipes, breeching, valves, duct work and other fittings. Designed with a high strength formula, Wet Wrap 'N' Seal permanently retains its strength, shape and form, requiring only 2-4 minutes to set. Simply submerge pre-cut cloth in clean water for 5 seconds, remove and wring out excess water and apply directly to affected surface. Follow all application instructions on label.

Fiberlock Technologies was founded upon the simple promise of providing the highest quality product and the best possible service to its customers while conducting business with the utmost integrity. Founded on the core beliefs that superior quality, definitive science and enduring service are the keys to corporate success, Fiberlock has grown to become one of the most respected names in the abatement and remediation industry.


Product Specifications:

  • WATER ACTIVATED ENCASEMENT REPAIR CLOTH: Permanently insulate and repair pipes, breeching, valves, duct work and other fittings with Wet Wrap 'N' Seal Thermal Insulation Repair.
  • HIGH STRENGTH, ONE-STEP INSTALLATION: Simply wet pre-cut Wet Wrap 'N' Seal cloth and apply directly to affected surface – cloth will set in 2-4 minutes, depending on temperature of immersion water.
  • APPLY QUICKLY AND EASILY: Save time and labor with Wet Wrap 'N' Seal. Once dry, insulation cloth permanently retains its strength, shape and form, requiring no maintenance and producing no waste.
  • LOWEST COST ENCASEMENT MATERIAL AVAILABLE: Wet Wrap 'N' Seal requires no special skills or tools for application and is free of any fumes or strong odors.
  • FOR OVER 35 YEARS, Fiberlock Technologies has manufactured products used to address environmental, safety and health hazards, becoming one of the most respected names in the abatement and remediation industry.

Product Insights

  • MFG SKU: 2432-U & 2433-U
  • Available in 4” and 6” x 9’ rolls (one case)
  • Applies quickly and easily
  • Free of fumes and odors
  • Permanently shaped
  • High-strength
  • Pre-cut to 9 ft. (2.7m) lengths
  • One-step installation
  • Saves time and labor
  • No maintenance
  • No special skills or tools required
  • No waste

PRECAUTIONS

  • Store in a dry place.
  • Approved respirators must be used to prevent inhalation of asbestos fibers that may be present in the air.
  • Protective clothing should be worn.
  • Asbestos abatement activities must be performed in accordance with all applicable regulations including EPA, OSHA, federal, state and local.
  • For more information always contact the appropriate agencies prior to beginning any abatement project.

Usage Instructions

SURFACE PREPARATION

Prior to application it is important to determine if the existing asbestos matrix is well adhered to the substrate. Correct any surface defects and clean all surfaces thoroughly. Be careful not to agitate asbestos fibers during preparation; this could increase asbestos exposure. If damaged, first apply a light collating of SerpiFlex followed by a second application. The second application should saturated the damaged area. Apply additional fiberglass, mineral wool or insulation cement to treated area if needed. Application Water in pail must be clean at all times. This product is a plaster of paris and synthetic resin combination. Use of skin protection or gloves is recommended.

  1. Hold loosely and submerge one Wet-Wrap ‘N’ Seal roll at a time in clean, tepid water (68°F/20°C) for 5 seconds. Keep thumb under edge of Wet Wrap ‘N’ Seal to avoid difficulty in finding starting end after squeezing.
  2. Remove and squeeze with twisting motion to wring out excess water, keeping thumbs under starting end.
  3. When applying overlap each layer by 50%. Smooth each overlap turn of Wet-Wrap ‘N’ Seal into the layers below, molding carefully to the contour, forming a solid, well fused covering. Note: For leather-tough protection and added strength, you can apply SerpiMastic over the Wet-Wrap ‘N’ Seal after it is dry.

SETTING TIME

Wet-Wrap ‘N’ Seal will set in 2-4 minutes. Setting time is measured from the point when the product is immersed to the point when it can no longer be molded. Increasing or decreasing the temperate of the immersion water by 9°F (5°C) will reduce or extend the setting time by approximately 15 seconds. Cleanup Tools and drippings should be cleaned with warm soapy water before adhesive dries. Dispose of waste according to all existing local, state and federal regulations.

PRECAUTIONS

Store in a dry place. Approved respirators must be used to prevent inhalation of asbestos fibers that may be present in the air. Protective clothing should be worn. Asbestos abatement activities must be performed in accordance with all applicable regulations including EPA, OSHA, federal, state and local.  For more information always contact the appropriate agencies prior to beginning any abatement project.

Resources

Safety Data Sheet (SDS)

Product Data Sheet (PDS))

  • MFG SKU: 2432-U & 2433-U
  • Available in 4” and 6” x 9’ rolls (one case)
  • Applies quickly and easily
  • Free of fumes and odors
  • Permanently shaped
  • High-strength
  • Pre-cut to 9 ft. (2.7m) lengths
  • One-step installation
  • Saves time and labor
  • No maintenance
  • No special skills or tools required
  • No waste

PRECAUTIONS

  • Store in a dry place.
  • Approved respirators must be used to prevent inhalation of asbestos fibers that may be present in the air.
  • Protective clothing should be worn.
  • Asbestos abatement activities must be performed in accordance with all applicable regulations including EPA, OSHA, federal, state and local.
  • For more information always contact the appropriate agencies prior to beginning any abatement project.

SURFACE PREPARATION

Prior to application it is important to determine if the existing asbestos matrix is well adhered to the substrate. Correct any surface defects and clean all surfaces thoroughly. Be careful not to agitate asbestos fibers during preparation; this could increase asbestos exposure. If damaged, first apply a light collating of SerpiFlex followed by a second application. The second application should saturated the damaged area. Apply additional fiberglass, mineral wool or insulation cement to treated area if needed. Application Water in pail must be clean at all times. This product is a plaster of paris and synthetic resin combination. Use of skin protection or gloves is recommended.

  1. Hold loosely and submerge one Wet-Wrap ‘N’ Seal roll at a time in clean, tepid water (68°F/20°C) for 5 seconds. Keep thumb under edge of Wet Wrap ‘N’ Seal to avoid difficulty in finding starting end after squeezing.
  2. Remove and squeeze with twisting motion to wring out excess water, keeping thumbs under starting end.
  3. When applying overlap each layer by 50%. Smooth each overlap turn of Wet-Wrap ‘N’ Seal into the layers below, molding carefully to the contour, forming a solid, well fused covering. Note: For leather-tough protection and added strength, you can apply SerpiMastic over the Wet-Wrap ‘N’ Seal after it is dry.

SETTING TIME

Wet-Wrap ‘N’ Seal will set in 2-4 minutes. Setting time is measured from the point when the product is immersed to the point when it can no longer be molded. Increasing or decreasing the temperate of the immersion water by 9°F (5°C) will reduce or extend the setting time by approximately 15 seconds. Cleanup Tools and drippings should be cleaned with warm soapy water before adhesive dries. Dispose of waste according to all existing local, state and federal regulations.

PRECAUTIONS

Store in a dry place. Approved respirators must be used to prevent inhalation of asbestos fibers that may be present in the air. Protective clothing should be worn. Asbestos abatement activities must be performed in accordance with all applicable regulations including EPA, OSHA, federal, state and local.  For more information always contact the appropriate agencies prior to beginning any abatement project.

Safety Data Sheet (SDS)

Product Data Sheet (PDS))

Product Reviews

Back to Asbestos